Important Plumbing Insights for Installing a Bathtub
Important Plumbing Insights for Installing a Bathtub
Blog Article
They are making several great points on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in the content beneath.
Setting up a bathtub isn't specifically rocket science, yet it does need solid plumbing, woodworking, and often, tiling skills. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old tub is conveniently available, the job can relocate rapidly; if you need to open up a wall to remove the old bathtub and also position the new tub, the job is much harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require a helper to vacate the old bathtub and set in the new one. See to it you have certified yourself for the work and fit trying it. Rather than employing a professional to take over a halfway-completed job, it is much better to think about utilizing one before you start. Possibilities are you may require a specialist plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your bathroom if you have actually already acquired a new bathtub as well as do not need to transform the arrangement of your previous water supply pipelines.
Your tools as well as product checklist must comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The procedure of getting rid of the existing taps can be fairly troublesome because of the limited gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly come from the pipes. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washing machines are in area in between the tap and also the sink. Protect the tap in position with the maker offered backnut. As soon as the faucet is firmly in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Making use of both wooden boards under its feet, place the bathtub in the needed setting. The wood boards are helpful in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little factors.
The following goal is to ensure that the tub is leveled all round. This can be attained by checking the level and changing the feet on the bathtub up until the spirit level checks out level.
To install taps, fit all-time low of the furthest versatile faucet connector to the proper supply pipe by making a compression join; then do the same for the other faucet.
Switch on the supply of water as well as check all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub must wait till the bath tub has actually been used a minimum of once as this will settle it right into its final setting.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final setting.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, triggering the water to pass through the wall surface in between the bath and the tiling, resulting in complications with wetness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and also cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealant can break fairly early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that write-up on Installing A Bathtub through an associate on our other domain. Do you know anybody else who is occupied with the topic? Take a moment to share it. I am grateful for your time. Kindly pay a visit to our blog back soon.
We're here 24/7, call! Report this page